Thursday, March 15, 2012
Thursday, March 8, 2012
Current sump/stand noise and future improvements
The overflows in the sump have started making noise, I think this is in the media boxes and is basically just water splashing as it comes into the top box. I put 90 degree elbows on the bottom of the bulkheads to try to get the water to spread out more evenly in the box, but I think all the stuff I put in the top media box (poret foam, bio-balls, other random crap for bacteria to colonize) has just started to accumulate enough junk in it now to be a little less free for water to flow through.
The result is that water splashes a bit in the top box making noise. I tried to fix this with a short piece of PVC with holes drilled into it, but that didn't really help. Over the weekend I think I will try a long piece-the length of the box-with lots of holes to try and let the water gently get into the media.
Alternatively, I think a trough in the bos that let's the water exit into a water filled "trough" then overflow out of that might work. Trouble is I am not quite sure what to use for that...
The Eheim 1262 pumps are somewhat variable in how much noise they make. The main noise source is vibration. Right now they are sitting on 2" thick Poret foam which helps a lot. I have some 5mm neoprene that I am going to try. I figure 20-25mm of neoprene might be quiet. As a bonus it will let the pumps sit lower in the sump making them less vulnerable to evaporation.
Finally, we need to get tops for the sumps made. I will probably get 1/4" thich glass tops, which is pretty thick but it means they are really strong and will insulate a bit better. This should help with temperature and evaporation (and maybe reduce noise even more :).
We added some 3/8" closed cell soundproofing found to the doors and sides of hte sump, which has cut down on noise some. We should get some mass loaded vinyl which I am going to use as a curtain across the open back of the sump to hopefully keep more pump and water noise in the sump. One concern is condensation inside the stand, but I think there will still be enough opening to keep that form being too serious and getting tops on the sumps will help as well.
Neoprene on its own is worse than the Poret foam. A layer of neoprene under the Poret foam may be an improvement. This seems the best. I think the goal is to "disconnect" the pumps from the tank as much as possible and the extra layer of neoprene under the foam seems to do that better. The slightly buoyant neoprene also probably helps here.
The result is that water splashes a bit in the top box making noise. I tried to fix this with a short piece of PVC with holes drilled into it, but that didn't really help. Over the weekend I think I will try a long piece-the length of the box-with lots of holes to try and let the water gently get into the media.
Alternatively, I think a trough in the bos that let's the water exit into a water filled "trough" then overflow out of that might work. Trouble is I am not quite sure what to use for that...
The Eheim 1262 pumps are somewhat variable in how much noise they make. The main noise source is vibration. Right now they are sitting on 2" thick Poret foam which helps a lot. I have some 5mm neoprene that I am going to try. I figure 20-25mm of neoprene might be quiet. As a bonus it will let the pumps sit lower in the sump making them less vulnerable to evaporation.
Finally, we need to get tops for the sumps made. I will probably get 1/4" thich glass tops, which is pretty thick but it means they are really strong and will insulate a bit better. This should help with temperature and evaporation (and maybe reduce noise even more :).
We added some 3/8" closed cell soundproofing found to the doors and sides of hte sump, which has cut down on noise some. We should get some mass loaded vinyl which I am going to use as a curtain across the open back of the sump to hopefully keep more pump and water noise in the sump. One concern is condensation inside the stand, but I think there will still be enough opening to keep that form being too serious and getting tops on the sumps will help as well.
Neoprene on its own is worse than the Poret foam. A layer of neoprene under the Poret foam may be an improvement. This seems the best. I think the goal is to "disconnect" the pumps from the tank as much as possible and the extra layer of neoprene under the foam seems to do that better. The slightly buoyant neoprene also probably helps here.
Thursday, March 1, 2012
Tuesday, February 28, 2012
110 Gallon Mbuna Setup
2.26.2012
Rinsed sand in tank
Water clarifier
2.27.2012
Full fill including sump
2.28.2012
Lengthen durso standpipe
Partial water change
Bacteria
Ammonia
3.1.2012
Water parameters same as tap water
3.4.2012
NH3 = 1ppm
NO2 > 0 ppm
3.5.2012
NH3 = 1ppm
NO2 = 0.25ppm
3.6.2012
NH3 = 1ppm
NO2 = 0.5-1ppm
3.7.2012
NH3 = 0.5ppm
NO2 > 1ppm
3.8.2012
NH3 = 0.5ppm
NO2 = 5ppm+
80% water change (tap water)
NO2 = 1-2ppm
3.9.2012
NO2 = 5ppm+
3.10.2012
NH3 = 0ppm
NO2 = 5ppm+
80% water change (tap water)
NO2 = 2ppm
3.11.2012
NO2 = 2ppm
80% water change
NO2 = 0.5-1ppm
3.12.2012
NH3 = 0ppm
NO2 = 5ish ppm
NO3 = 30-40ppm
3.13.2012
NO2 = 2-5ppm
3.14.2012
NO2 = 1ppm
Rinsed sand in tank
Water clarifier
2.27.2012
Full fill including sump
2.28.2012
Lengthen durso standpipe
Partial water change
Bacteria
Ammonia
3.1.2012
Water parameters same as tap water
3.4.2012
NH3 = 1ppm
NO2 > 0 ppm
3.5.2012
NH3 = 1ppm
NO2 = 0.25ppm
3.6.2012
NH3 = 1ppm
NO2 = 0.5-1ppm
3.7.2012
NH3 = 0.5ppm
NO2 > 1ppm
3.8.2012
NH3 = 0.5ppm
NO2 = 5ppm+
80% water change (tap water)
NO2 = 1-2ppm
3.9.2012
NO2 = 5ppm+
3.10.2012
NH3 = 0ppm
NO2 = 5ppm+
80% water change (tap water)
NO2 = 2ppm
3.11.2012
NO2 = 2ppm
80% water change
NO2 = 0.5-1ppm
3.12.2012
NH3 = 0ppm
NO2 = 5ish ppm
NO3 = 30-40ppm
3.13.2012
NO2 = 2-5ppm
3.14.2012
NO2 = 1ppm
110 Tropheus History
2.26.2012
25% water change (tap water)
Concerned about 2 fish lurking near surface, but all fish eat
2.27.2012
1 fish severely distressed in the morning, removed to hospital tank but died within 10-15 minutes
1 fish lethargic/less responsive at lunchtime, removed to hospital tank and dosed with metro
1 fish distressed in evening, removed to hospital tank
Double dose Metro main tank
2.28.2012
1 fish died in hospital tank overnight (probably the one removed evening of 2.27)
1 new fish not eating, but not lethargic enough to be caught easily to move to hospital
40% water change main tank
Double dose Metro main tank
2.29.2012
Removed 1 distressed fish to hospital tank
1.3g Metro (last of Fish Zole)
Water change and double dose Metro for hospital tank
3.1.2012
Distressed hospital fish (2.29) died during the day
Other two hospital fish mouth metro food but spit (also spit regular food)
3.2.2012
Two hospital fish ate some, spit some in a.m., ate all in evening
40% water change main tank
2tbsp Metro main tank (pure Metro)
Removed AC110
3.4.2012
40% water change main tank
2tbsp Metro main tank (pure Metro)
Water good post removal of AC110
3.10.2012
Small fish spitting food, moved to hospital tank
Two fish from hospital tank returned to main tank
One of fish returned to main tank is lurking, caught and returned to hospital tank
3.12.2012
Returned fish had lip injury, treated with Pimafix/Melafix
3.13.2012
Returned fish looking worse after work (lip and side with white fluff), added Erythromycin
Returned fish died late night
3.14.2012
Bloat hospital fish dead in the morning
3.25.2012
Beat up skinny fish, but still eating
3.26.2012 p.m.
Beat up skinny fish lethargic, no interest in food
Moved to hospital tank but abruptly got worse; dosed with Clout but died within hours
Weeklong dose of Metro for main tank
25% water change (tap water)
Concerned about 2 fish lurking near surface, but all fish eat
2.27.2012
1 fish severely distressed in the morning, removed to hospital tank but died within 10-15 minutes
1 fish lethargic/less responsive at lunchtime, removed to hospital tank and dosed with metro
1 fish distressed in evening, removed to hospital tank
Double dose Metro main tank
2.28.2012
1 fish died in hospital tank overnight (probably the one removed evening of 2.27)
1 new fish not eating, but not lethargic enough to be caught easily to move to hospital
40% water change main tank
Double dose Metro main tank
2.29.2012
Removed 1 distressed fish to hospital tank
1.3g Metro (last of Fish Zole)
Water change and double dose Metro for hospital tank
3.1.2012
Distressed hospital fish (2.29) died during the day
Other two hospital fish mouth metro food but spit (also spit regular food)
3.2.2012
Two hospital fish ate some, spit some in a.m., ate all in evening
40% water change main tank
2tbsp Metro main tank (pure Metro)
Removed AC110
3.4.2012
40% water change main tank
2tbsp Metro main tank (pure Metro)
Water good post removal of AC110
3.10.2012
Small fish spitting food, moved to hospital tank
Two fish from hospital tank returned to main tank
One of fish returned to main tank is lurking, caught and returned to hospital tank
3.12.2012
Returned fish had lip injury, treated with Pimafix/Melafix
3.13.2012
Returned fish looking worse after work (lip and side with white fluff), added Erythromycin
Returned fish died late night
3.14.2012
Bloat hospital fish dead in the morning
3.25.2012
Beat up skinny fish, but still eating
3.26.2012 p.m.
Beat up skinny fish lethargic, no interest in food
Moved to hospital tank but abruptly got worse; dosed with Clout but died within hours
Weeklong dose of Metro for main tank
Saturday, February 25, 2012
110 Tropheus Maintenance
Added 6 dwarf petricola 1in
Added AC 110 with established media
Nitrite = 0.5ppm
Changed 1/3rd water using water from 75 gallon.
Added AC 110 with established media
Nitrite = 0.5ppm
Changed 1/3rd water using water from 75 gallon.
Subscribe to:
Posts (Atom)